U-Boot for the LG Optimus 2X P990

DISCLAMER! Moving your device to use U-Boot assumes replacement of the vendor bootloader. Vendor Android firmwares will no longer be able to run on the device. This replacement IS reversible.

Quick Start

  • Build U-Boot

  • Process U-Boot

  • Flashing U-Boot into the eMMC

  • Boot

  • Self Upgrading

Build U-Boot

$ export CROSS_COMPILE=arm-none-eabi-
$ make star_defconfig
$ make

After the build succeeds, you will obtain the final u-boot-dtb-tegra.bin image, ready for further processing.

Process U-Boot

DISCLAMER! All questions related to the re-crypt work should be asked in re-crypt repo issues. NOT HERE!

re-crypt is a tool that processes the u-boot-dtb-tegra.bin binary into form usable by device. This process is required only on the first installation or to recover the device in case of a failed update.

Permanent installation can be performed either by using the nv3p protocol or by pre-loading just built U-Boot into RAM.

Processing for the NV3P protocol

$ git clone https://gitlab.com/grate-driver/re-crypt.git
$ cd re-crypt # place your u-boot-dtb-tegra.bin here
$ ./re-crypt.py --dev star

The script will produce a repart-block.bin ready to flash.

Processing for pre-loaded U-Boot

The procedure is the same, but the --split argument is used with the re-crypt.py. The script will produce bct.img and ebt.img ready to flash.

Flashing U-Boot into the eMMC

DISCLAMER! All questions related to NvFlash should be asked in the proper place. NOT HERE! Flashing U-Boot will erase all eMMC, so make a backup before!

Permanent installation can be performed either by using the nv3p protocol or by pre-loading just built U-Boot into RAM.

Flashing with the NV3P protocol

Nv3p is a custom Nvidia protocol used to recover bricked devices. Devices can enter it by pre-loading vendor bootloader with nvflash.

With nv3p, repart-block.bin is used. It contains BCT and a bootloader in encrypted state in form, which can just be written RAW at the start of eMMC.

$ ./nvflash_v1.13.87205 --bct star.bct --setbct --odmdata 0xC8000
  --configfile flash.cfg --bl android_bootloader.bin --sync
$ ./utiils/nvflash_v1.13.87205 --resume --rawdevicewrite 0 2048 repart-block.bin

When flashing is done, reboot the device.

Flashing with a pre-loaded U-Boot

U-Boot pre-loaded into RAM acts the same as when it was booted “cold”. Currently U-Boot supports bootmenu entry fastboot, which allows to write a processed copy of U-Boot permanently into eMMC.

While pre-loading U-Boot, hold the volume down button which will trigger the bootmenu. There, select fastboot using the volume and power buttons. After, on host PC, do:

$ fastboot flash 0.1 bct.img
$ fastboot flash 0.2 ebt.img
$ fastboot reboot

Device will reboot.

Boot

To boot Linux, U-Boot will look for an extlinux.conf on MicroSD and then on eMMC. Additionally, if the Volume Down button is pressed while booting, the device will enter bootmenu. Bootmenu contains entries to mount MicroSD and eMMC as mass storage, fastboot, reboot, reboot RCM, poweroff, enter U-Boot console and update bootloader (check the next chapter).

Flashing repart-block.bin eliminates vendor restrictions on eMMC and allows the user to use/partition it in any way the user desires.

Self Upgrading

Place your u-boot-dtb-tegra.bin on the first partition of the MicroSD card and insert it into the device. Enter bootmenu, choose update the bootloader option with the Power button and U-Boot should update itself. Once the process is completed, U-Boot will ask to press any button to reboot.